Search results

what kind of times do you guys get from quarter miles?? proper timed runs with slips? the quickest ive had from my first day dragging was 14.9@ enniskillen straightliners with a wet track. i want to improve on this obviously so am asking what mods you quicker guys have. my car spec... b16b...

had my ek9 photographed by MartyMoore there last week, great photos taken, let me know what ya's think!! :D

just noticed this today, when driving the voltage on the neo is jumping between 12.00 v up to 13.8 or so nearly constantly, yet if i turn the lights on it stays at 13.8 or so....what would cause this??:angry2:

before i get the car mapped, would it be an idea to get this done? to they fall out fo correct tolerances easily or should mine be ok? dont know when they were last checked. is this expensivce to get done and would it improve horsepower/ reliability? cheers lads

anyone ever used or heard much about these manifolds? you will see pictures of the exhaust a little down the pg N1 Exhaust System Performance Buddy Club Body Kits, Alloy Wheels & Performance Parts - Urban Performance i have one on the car and am trying to figure out if i should upgrade?

hey guys, is it necessary to wire the VTM signal in when doing this? its just in the wiring diagram it doesnt state where it is on my ecu yet on pg 7 of instructions it has it listed as needing to be hooked up?? any feedback be great! steve

well guys i want to remove the air con form the ctr to free up some extra power and get rid of the weight, like i dont really need it in this country ya know??? whats involved in it?bt:)

have this wee minter about 3 months so just thought id throw up a few pics, spec so far is 98 ctr n1 4-1 mani de-cat buddyclub spec 4 full system itg maxogen cai carbon intake, magnecor leads iridium plugs orc clutch orc flywheel buddy club quick shift buddyclub vtec controller...

well guys, ive a buddyclub spec 4 on my 9 at the minute and love it to pieces, but i was wondering what other peoples opinion are on these and what systems might be better?? also the system is 2.5" isn't that correct? reason im asking that is the dyno operator thought it might be tooo big for...

pics of the ek9 on the rollers in westward... YouTube - car stuff 004http://www.youtube.com/watch?v=qvY26MppOzY and on mondello

well lads, after a trackday saturday ive notice the pedal has become a lot softer and it was happening on the track, taking more effort to stop the car! is this either down to the pads being fuked or did i just boil the brake fluid, sme has evaporated and i jus need to change that to high...

guys i might be picking up a vafc later this week, its a vafc1 and im jus concerned about the installation, i dont want to buy a bogey unit. the chap im getting it off told me there is 11 wires coming out of it....would this be correct? reason im going for this is im on a budget and am getting...

my ek9 has adj rear camber arms, can anyone tell my the ideal amount needed on the back for optimum handling? as she is now its kicking the top of the wheels in a fair bit.... will try get a pic up or that! just i dont want it set up wrong for mondello!:D

guys have a problem with my cars speedo, every so often if i drive hard the speedo needle spikes up and down and then stops at 0 then might climb up intermitinly, im guessing its the speedo sensor on the gearbox. maybe its come loose due to the harsh twin plate clutch or its fudged...

guys my next mod for the civic is going to be gearbox work, it already has an orc twin plate clutch and light flywheel so im going for either a 4.9/ 4.78 fd or a 3 4 and 5 gear set from m factory...what wll give the best gains??

here is my ek9, let me know what you think!!:D mods are orc clutch and light flywheel, n1 4-1 mani, de-cat, buddyclub spec 4 system, itg carbon airbox w' cold air feed,magnecor leads and uprated plugs, buddyclub quickshift and vtec controller, buddyclub rear camber arms, adjustable suspension...

hey guys, i have a 4-1 mani on my ek and im thinking on heat wrapping it. is there much point in doing this or would i be wasting my time?? regards, steve

hey guys im a new user from dublin! got an ek9 myself with a few mods,orc clutch and light flywheel, n1 4-1 mani, de-cat, buddyclub spec 4 system, itg carbon airbox w' cold air feed,magnecor leads and uprated plugs, buddyclub quickshift and vtec controller, buddyclub rear camber arms, adjustable...