Search results

Recently did a b18b1 in an ek4 swap... I did the wiring myself... it started up and runs fine! But I retrived this code after the check engine light lit up! My question... I was told to match the colors on the crank fluctuation sensor (I think that's what its called) and it had a ground, the...

USDM 96 B18B1 into a 96 EK CX... I have the swap all good to go just need to do the wiring and im done.... What wires do i splice together on the Crankshaft sensor? The B18B1 has a two wire (blue w/ red stripe and yellow w/ red stripe) plug and the D16y7 has a three wire (blue, yellow...

I know its old and its been covered, but just to remove any doubt in my head hahahaha Remove IAC valve (two wire) plug from DC2 harness Match black wires on my civic harness and leave the other one out.... On ecu plug.... move the black and diconnect the orange? I have the pinnout and...

Real quick, does anyone know the gauge and type of wire used in the engine harness? I'm going to extend some wire here and there to clean things up... also .... a twist, solder, and heat shrink is the best connection, 2nd to no splicing at all correct?! Thanks you guys:thanks:

A 96-01 DC2 shift linkage cannot be used in a 96-00 EK hatch...

Dropping in a b18 into my ek4... do I really need the front tranny and "ac" engine mounts? Can I get away with just the three main mounts? Thanks everyone in advance for the input!

My d16y7 in my 96 cx hatch spun a bearing and I drove it 72 miles till it blew through the block, 1 mile from my house. Good times hahahaha. I'm going to swap in a b18b (LS engine in the U.S). It has been a long time since I've done a swap and wanted to make sure I have all the proper parts...

Can anyone explain or put up a picture of what the ST FRONT SWAY BAR (W/O original bar) bolt up? I have a 96 Civic CX and just bought my F7 LCA's and the ASR 24mm Sway with the reinforcement brace and want to bolt on a front sway before bolting on the rear.... CX's did not come with sway bars...

I've got a 96 honda hatchback cx, I love the short shifter in it now and I'm a cheap ass... I don't want to buy another one and was wondering if I can use this shifter with the integ linkages? I'm doing a swap and wanted to know if I could still keep it.... thanks guys

Whats up guys! Hopefully everyone had a good thanksgiving.... Does anyone know if 96-99 GSR's come with an E.G.R system or E.V.A.P system? Thanks.... I hate the E.G.R. and im doing a swap in a 1996 Honda Hatch CX....

Hey whats up guys... Anybody ever here about the MSD dash hawk? I want to keep tabs on my readings and my rpms are off on my tach (messed up 99/00 Si cluster). I dont want to spend lots of money on a stand alone or hondata... i dont trust cigarette lighter meters (gmeters hahahaha)... The one...

What's up! I have a 96 civic hatchback cx and just bought a complete disk swap that's from a 96 gsr abs! Everything looks cool... abs sensors could just come off.... the booster is cool too but the master cylinder! The master cylinder on my car has 2 lines coming from the passenger side to the...

Alright, I've heard of people using 225 tires up front and leaving the 205's in the rear. What offset do people use in these setups? I want to start nasa hpde heavily in my new ek4 I picked up a week ago! I ran 235 fr and 215 rear in my dc5! the car felt a lot better....

I bought my 96 HB CX with, what looks to be, a 99/00 gauge cluster...... Anyone know how to calibrate it er something? The rpms are pegged all the way down at idle and doesnt start moving till what seems to be about 900 - 1100 rpms! Also the temp gauge is pegged well below the lines on the...

Hey guys. I will get straight to it..... I have a 96 Hatch CX, i want a b18b (for now) for hpde as a start.... What do i need besides the axles, ecu, engine/transmission and shift linkage? b18b is a bit more fun than the d16 in there now and comes with more torque for track days. Also, a huge...

I will make this quick.... I am going to swap the engine later on but really want to focus on brakes and suspension first (that matter to me the most). I am getting bombarded with all kinds of crap on brake conversions; 4x100, 4x114.3, gsr, civic type r, jdm, usdm..... you get the picture. I...