Search results

As title, does anyone have any, or know where I can get a hold of them in a hurry?

I posted this in my project thread, but it'll probably fit here. Me and four other guys rented a tiny track outside of Trondheim, Norway and had a go. All footage is from my car. My EK4, one EJ9, one DC2, an EJ6 and a Legend(!) which doesn't show in the movie. It was pretty much a storm...

I need the bushings that go under the radiator (and the top bracket if you\ve got one kicking about). Also, I need the hose and pipe that connects from the head cover to the intake arm, for a B18C6/5/R

Must be shipped to norway. :) Let me know whatcha got! :D

Drop me a line if you have one you want to get rid of :) Don´t know if the pre/post facelift ones are different...?

So, I´ve done a 5-lug swap, and I threw the DC2 knuckles straight onto my EK4. Bolted right up as you´d expect. But now I´m running yellow konis with Eibach springs, and it´s a bit too low in the front versus what I´d expect. I´m using a set of 15x6.5 ET39 wheels with 195/55 tyres in the...

I´ve got a set of DC2 seats with rails, and as expected, only 3 of 4 bolt holes line up. As far as I can figure out, the EK9 rails bolt up to both my EK4 and the DC2 seats. So I want some. Anyone?

I´ve done a 5-lug swap on my EK4, the donor bits were from a 98 spec UKDM DC2. It´s lowered 35mm with a koni/eibach prokit combo. Currently running OE DC2 wheels for winter, which seem great weight- and strengthwise. Just may go for another set for track use. But - for summer, it looks like...

I´ve just installed my Koni/Eibach combo and for some reason, it´s just stupid low in the front. If there are grooves in the road the exhaust manifold will actually drag along the center.. :nerv: I´ve installed on the "standard height" spring perch notch, so I´m starting to wonder if I...

I'm looking to kick out my Koni coilovers and go for a damper/spring setup. If I'm going to be sensible about it, the car will be a 95% daily driver, and I have no need for 7-way adjustable Öhlins coilovers with external reservoir and automatic corner weighting. So - I'm thinking I'll start...

I purchased a bone dry 98 spec DC2 gearbox, and I figured I´d fill it tonight. However, it sits in an EK4, and there really wasn´t much room to work with hoses and funnels to fill it through the proper hole. As far as I knew, you can fill the gearbox through the breather hole, so I did. But -...

I'd like to buy a temp sensor plug (with a little pigtail on it) so I can solder it onto my existing wiring. Lemme know what you have. :D EDIT : Got it!

I tried searching and Googling a bit, but couldn't really find anything. I'm doing a 5-lug conversion on my EK4 (donor parts are from a 98 spec UKDM DC2). The abs wires from the DC2 were cut, and I had some new ones for my EK4's rear lying about. However, these don't fit the DC2 parts. Which...

I am celebrating my 50 posts and my jubilee as a seasoned EK9.org user with a WTB post! Whoo! Ok, I´m after an exhaust that is not ridiculously loud. Something along the lines of the Twinloop and the OE EK9 exhaust. Ideally I need a cat as well, and preferrably it should bolt up to my OE...

Engine/gearbox : JDM B18CR BWR Gear linkage polybushes DC2 Gearbox (98 Spec 4.7FD, LSD) DC2 Gen. 2 Driveshafts DC2 Airbox EK9 Cat EK9 shifter and linkage Fidanza lightweight flywheel Mishimoto radiator Mishimoto fan shroud Mugen EK9 TwinLoop exhaust Mugen header Tegiwa Engine Damper Walbro 255...

When I post a PM to some users, I am getting a 500-message (Internal server error). The url it fails at is : http://www.ek9.org/forum/private.php?do=insertpm&pmid=[pmid]

Perhaps someone on here have knowledge regarding my current brake issue; I've got a '96 EK4 and a '95 Del Sol ESi. The Sol has the same brakes as the eg6 civic VTi. As the EK4 also is a VTi (Type-S), I would think the front pads were somewhat similar, but they are in fact smaller. The front...

If there's feedback to be given, give it here. :)

Thought I'd say hi, even though I don't have an EK9 - RHD Jap cars are impossible to import here in Norway. But I do have an EK4 and a pleasing disposition! I figured this would be an interesting forum both parts- and tech-wise. :)