Official post your dyno RR thread!!


blinx9900

blinx9900

Super Moderator
Joined
Dec 5, 2006
Messages
10,880
This thread is going to be a compilation or dyno charts from everyone.

If you would like to contribute please post the following:
-Picture of your dyno chart
-Related mods(you don't need to list your ICE or suspension mods ;) )
-If the dyno chart is hard to read please list numbers and unit of measure like if its bhp or whp or nm or lb ft etc...
-Type of dyno if known example: dynojet 248, dynopack, dynodynamics etc...
-Thats it!

I prefer not posting photo's of your car but if you feel you must please just post 1, i don't want this to become a show and shine thread ;)

I'm also going to put links to other threads on this front page that i think are helpful and have dyno charts listed feel free to pm me any links you find:

http://www.ek9.org/forum/resource-area/9719-jimbobs-b18c-ek9-hondata-tuned-comparisons.html
http://www.ek9.org/forum/resource-area/7159-stock-ek9-hondata-tuned-162-7whp-190bhp.html
http://www.ek9.org/forum/resource-area/7767-ek9-ihe-cams-hondata-tuned-177-6whp-207bhp.html
http://www.ek9.org/forum/photos-videos/7464-dyno-results.html
http://www.ek9.org/forum/engine/6228-back-dyno.html
http://www.ek9.org/forum/general-chat/6102-85x89-dyno-tuned.html
http://www.ek9.org/forum/honda-inte...dyno-results-stock-integra-type-r-engine.html
http://www.ek9.org/forum/engine/4703-been-dyno-need-some-advice-vtec-point.html
http://www.ek9.org/forum/engine/3506-my-b16a-dyno.html
http://www.ek9.org/forum/general-chat/4147-new-dyno-numbers.html
http://www.ek9.org/forum/projects/4129-my-dyno-sheet.html
http://www.ek9.org/forum/general-chat/3934-new-dyno-numbers-new-setup.html
http://www.ek9.org/forum/photos-videos/2551-jugbugz-early-dyno-old-video.html
http://www.ek9.org/forum/general-chat/2266-post-your-b16b-dyno-s.html
http://www.ek9.org/forum/photos-videos/233-my-ek9-dyno.html
http://www.ek9.org/forum/photos-videos/233-my-ek9-dyno.html
http://www.ek9.org/forum/photos-videos/2607-my-ek9-rolling-road.html


if you want your thread removed from this thread or you have a more up to date thread PM me and i will make the change.

Even if you don't have a chart handy but you know your numbers post them UP!!!
 
Last edited:
Mine!

Stock B18C ITR 98 Spec Engine
Mugen Intake
Mugen Header
RS*R Exhaust
Apexi Power FC ECU

Dynojet

171 whp
121 lb/ft torque

attachment.php



Video:

YouTube - JDM Integra Type R 98 Spec Dyno Run
 
b20vtec NA

b20z bottom
b18c5 type r head
type r intake manifold
2.5 exhaust 4 in 1 headers
2.5 down pipe straight
cold air intake
5 inches inside diameter muffler

250whp @ 7k rpm
 
jomaripretty said:
b20vtec NA

b20z bottom
b18c5 type r head
type r intake manifold
2.5 exhaust 4 in 1 headers
2.5 down pipe straight
cold air intake
5 inches inside diameter muffler

250whp @ 7k rpm
Click to expand...

do you have a dyno? That seems to be a lot of power at only 7000rpm...
 
yeah and not to mention no listing of what cams or if any portwork and overall static compression.
 
7th May 2009
Location - Hong Kong
Outside temperature - 29 degrees
Humidity - 80%

Car:
EK4 - B16A4
ITR cams
Ported head (blending and smoothing) on a ITR head
Stock bottom end
3" custom intake with BPI+K&N filter
HKS cam pulley @ +1 , -1
5-zigen manifold
Mugen backbox + 2.5" mid de cat piping
Stock NGK 6 sparkplugs
Shell V-power fuel
64mm throttle body
Skunk 2 (old version) intake manifold
Outlaw engineering heatshield gaskets
Power-fc ECU for B18C tuned using Pro Commander

AFR graphs
IMGA0043.jpg


Torque (KG.M) vs PS
IMGA0034.jpg


Final tune (193hp @ 8900rpm
IMGA0045.jpg



Fine tuning to be done later to smooth it out a bit by tweaking the cam timings and ignition timing, not enough time on the dyno.
________
WATER BONGS
 
Last edited:
Hears mine!:nice:

SPEC
JDM B18C engine
oem 4-1 manifold (heat wrapped)
Baffeled de-cat
full Fujitsubo exhaust system
70.00mm Throttle body (with inlet to match)
HKS racing suction system
10mm nology hotwires HT leads+ngk irridium plugs
HKS Grounding kit
7.5 lb flywheel
Exedy stage 1 clutch
Hondata S300 (with custom WILL tune);)

This was done on a Dynojet reading in whp & lbft

2278052120102890423S600x600Q85.jpg
 
Car: JDM EK4 Civic Ferio
Mileage on engine: More than 215,000km

Engine specs:
JDM B16A4 engine
JDM ITR airbox with K&N cone air filter
JDM ITR 62mm throttle body (bored to 63mm on the inlet side)
JDM ITR intake manifold
JDM EK9 camshafts
JDM EK9 valvesprings
JDM EK9 81mm pistons
Toda cam gears (zero-ed)
3-angle valve job
NGK BKR7E spark plugs
HKS 4-2-1 exhaust manifold
Original EK4 catalytic converter
JDM ITR B-piping
JDM ITR rear muffler
JDM ITR gearbox with 4.785 FD and helical LSD
JDM EK9 clutch
Spoon 4.2kg flywheel
Unichip

7421d1253868049-200bhp-b16a-98-civic-ek4-dyno_crank_17jul09.jpg
 
Last edited:
B20 block (blueprinted by ERE)
B18 ITR head (w/ PnP work by ERE)
Supertech Valvesprings / Retainers
Skunk2 Pro3+ camshafts
ARP Head Bolts
Edelbrock VictorX Intake Manifold
Erick's Throttle Body
HP Racing custom headers
84mm CP Pistons
Eagle Connecting Rods
OEM 89mm crankshaft
Edelbrock fuel pump
450cc injectors
MSD external coil
HP Racing crankcase/valvecover tank-breather system
tuned on Crome, E85
Exedy Hyper Comp Twin Plate

241whp @ 9300rpm, 166 ft-lbs @ 5500-6500 rpm




B16B block / head (w/ PnP work by ERE)
Supertech Valvesprings / Retainers
Ferrea Valves +1mm
Manley 'Turbo-Tuff' rods
Endyn Roller Wave pistons
OEM 89mm crankshaft
Darton MID Sleeves
ARP head bolts
Cometic head gasket
Moroso alum. oil pan
Skunk2 Pro1 camshafts
JG Victor X Port-matched intake manifold
Blox 74mm throttle body
MSD Pro billet distributor
Crane PS92 coil
T1 Race Development Pro10 ignition package
4-bar MAP Sensor
HP Racing custom front face turbo manifold
Custom air-to-water intercooler set up
2x Bosch 044 fuel pumps
Garrett T4/T67 Q-trim turbocharger
2x Tial Waste Gate
Tial 50mm bov
Rochester 1600 cc Injectors
Aeromotive fuel reg
HP Racing custom sumped OEM gas tank
HP Racing crankcase/valvecover tank-breather system
Exedy Hyper Comp Twin Plate
tuned on Neptune

753.2whp @ 8000rpm, 533.6lb-ft tq @ 6000rpm
boost was 37psi on E85

outyiv.jpg


both on Dynapack
 
Last edited:
You must log in or register to reply here.
Back
Top