Search results

How it looked when i bought it August 09 12 months and a lot of money and stress later b16a2 engine conversion - before it was fitted, it had a major service including new water pump, tensioner, timing belt, piston rings, valve stem oil seals, head gasket exedy stage 1...

I have decided to sell my honda civic. I bought it as a standard 1.4i fusion and ive spent a small fortune on it. The car currently has less than 61,000 on it, i purchased it with 57,000. Quick spec list b16a2 engine conversion (professionally fitted) - before it was fitted, it had a major...

Seen these and wondering about them Integra Civic Type R 2.5" exhaust gasket donut JDM ek9 on eBay (end time 07-May-10 18:21:50 BST) Just my 5zigen has a couple of metal wires (tiny things) poking out at where it should connect to the cat/decat and wondering if a donut gasket might sort...

If putting a new manifold on an ek4 with a 2.5 collector, should i get a decat for an ek9? Dont want to get an adjustable decat because i dont like welds Thanks :nice:

My coilovers were put in and my mechanic set them to the hardest (meisterR's), its been about a month now or so and i want them softened as i cant even listen to cd's now because they just keep skipping and jumping the roads are so bad. I cant work out how to get to the top of the rear...

If im going for a manifold i would like a 2.5 instead of a 2.25 (i have an ek4), does a manifold for an ek9/dc2 sit much lower (5zigen to be prescise) than a 2.25 for an ek4? Would just be worried about scraping/denting it Thanks! :nice:

As title really :thanks:

Sorry if this has been asked loads but i dont know what to search for and i couldnt find the answer anywhere. Basically i still have my standard manifold (2.25) and a decat (2.25) but my new cat back is 2.5, will it still just bolt straight on or will i need something to make it adapt...

As title, am after an iacv. Would like low mileage to Need the one that fits the bottom, middle size please. Not the left one! :thanks:

Am considering a DC Sports 4-2-1 manifold but am hearing some mixed reviews on them. Some good comments are some bad, what are the opinions on these? I dont mind if its a few bhp less than toda, spoon, etc, as long as i see ok gains and the build quality will last

Is there any difference with the Integra iacv, Civic ek4 or ek9 one? Also ordered new gaskets and need to know which iacv is my fitment (bottom two in the picture), is there anyway of spottin the difference without removing the unit (havent had a chance to look yet sorry!)

Think Ive decided on the BC Pro spec exhaust but just wondering does anyone know the width (like 2.25 or 2.5) of it? Also, is there any difference polished stainless stell and brushed? Also, if i purchase a dc sports manifold for a b16a2, would it be 2.25? Thanks :nice:

As title, need a brake proportioning valve of a Civic ek4 or ek9 that didnt have abs. Should look same as picture below (6 ports!) Let me know, Thanks :)

Just a quick question. I have an ej9 with Integra brake conversion (4 disc's) so i want to change the proportioning valve to a civic that has 4 discs. What ones can i use that will fit? (my cars a 99 facelift) Was there any difference with the facelift and pre facelift valves? Can i use...

With the cold, damp mornings my car is struggling a little when the engine is cold. When i am moving and press the clutch in (either to stop or change gear) and the revs drop should drop to idle, sometimes my engine just cuts completly and can have a little trouble getting started again. Only...

Got my car broke into and my locking wheel nut was stolen (was from Tegiwa/sprint wheel). Personally loved them and hate silver wheel nuts now, can anyone recommend some red wheel nuts and locking nuts to, please (that arent rays because i couldnt afford them!). Something reasonably priced...

As title, is there any difference between the two?

Just wondering if anybody could help me. Hopefully in the next couple of weeks I'm gonna get Innovative engine mounts for my b16, did like Hasport but they are far too expensive! Most places I've looked only deal them to the U.S. Does anyone know a good thats reasonable money wise please...

Bit of a problem here, when Im sitting idle for a while, the water temperature gauge will rise to about half way and the fan will kick in as it should but when i start to drive or move anywhere, the temperature gauge drops to freezing cold again. Can anyone help please? :angry2: Don't know if...

Can anyone tell me the differences between the two? As far as i can tell, one looks chrome/polished and the other looks black just. Is there really any difference apart from looks? And would 60A Red be more than enough for street use? Thanks