Bisimoto V2 Manifold


Status
Not open for further replies.
T

type-r-mad

Member
Joined
Jun 2, 2007
Messages
357
Item - Bisimoto v2 custom made header from drag car specalists in canada, header was custom made to my specification, i noticed massive difference low down torque AND top end with this header, also included is a custom made decat, as the downpipe on this manifold is 3 inch and will not fit an unmodified honda cat, but i have a 3 inch decat with a 2.5 inch exit flange so you can still bolt a normal exhaust without any problems, i ran mine with a spoon n1 and b pipe

location - central scotland ( can post anywhere at extra cost )


condition - perfect, only been on the car 54 miles for 1 track day.

price - 750

pictures -
34252_441269149873_699244873_5764017_1626740_n.jpg

28580_421930354873_699244873_5264366_4159022_n.jpg

31374_419615214873_699244873_5216686_7233153_n.jpg

26724_384306459873_699244873_4809810_5662644_n.jpg

26724_384305174873_699244873_4809808_37148_n.jpg

26724_384304049873_699244873_4809807_2451654_n.jpg

66503_481738689873_699244873_6712025_6209692_n.jpg


***please note, to use this header you must remove aircon***
 
Last edited:
iv seen this in real life and its amazing.
 
Cant really give you approx gains but bisimoto claim a 17 whp gain when they remapped a standard car with the header on average on the forums its around 15-20 bhp gain once mapped for it, every car is different though, but even without being remapped i felt a difference with mine fitted
 
What are the specs of your engine that this manifold is custom-made for?

Looks evil!! i like it !
How is the ground clearance?
 
my engine wasnt anything drastic, b18c4 with skunk2 inlet manifold, blox 70mm throttle body, spoon n1, spoon b pipe, hondata s300, hondata intake gasket, and the bisi manifold, j's racing intake, aem wideband. and the car was on a basemap, was approx 200bhp. mapped it would have been interesting to see with the header fitted, but i never got round to it sadly, and the manifold is good for clearance, it sits really close to the sump, fits like a glove, its around 5mm off the subframe aswell, and the downpipe points up towards the tunnel with an angled flange so it sits the exhaust in a slightly higher position aswell
 
Bisi moto is in Ontario, California (yes there is another ontario) :secret:
 
This is just for asking, but aren't those retailed brand new for 650 usd..?
 
P4X said:
This is just for asking, but aren't those retailed brand new for 650 usd..?
Click to expand...

$650 that would be nice!! been emailing to Bisi as im after one , the V2 delivered to your door from there work shop is $910, thats for the stainless option! which is very cheap and brandnew!! with the exchange rate at what it is at the moment! :drool:
 
Jimbo said:
$650 that would be nice!! been emailing to Bisi as im after one , the V2 delivered to your door from there work shop is $910, thats for the stainless option! which is very cheap and brandnew!! with the exchange rate at what it is at the moment! :drool:
Click to expand...

i read in theyr website that the base stainless steel manifold is 649 usd... i don't know how much they take for delivery...:nerv:
 
This car is beutiful mate i read about it in banzai...... the shot of you sitting on the gerder with joe the chap from banzai is in my garage on the wall.
if you weren't in banzai and bought it of the old owner sorry about that, nice car though man.
free bump i guess
 
Status
Not open for further replies.
Back
Top