Search results

Hi guys, Some of you might have seen my MG ZR rally car which I put a B16 engine into? Well here's a few recent shots to keep you updated. I had a slight mishap at a test session the other week and have done some engine damage - perhaps you guys may be able to help advise me? Engine is a B16A...

Hello guys. I have googled this all day and plenty of people reporting the same issue but no proper conclusion resolved. My car is on the dyno and it has a calibration loaded that runs and idles beautifully but won't Rev passed 2500rpm. To give a background on the situation, I have fun the car...

As title, looking for a set of cams with adjustable Verviers, uprated springs and retainers for a B. Skunk 2 pro 2's or similar would be great. Let me know what you have?? Many thanks, John

Description: Here I have for sale a set of brand new 4 RC Engineering Flow Matched 370cc Fuel Injectors - RC Part# SL4-370. Flow Rate - CC's: 370 CC's / MIN @ 43.5 PSI Flow Rate - LB's: 35 LBS / HR @ 43.5 PSI Resistance: 12.5 Ohms @ 68 F Voltage: 8-15 Volts, nominal 13.5 Volts Amperage: 1.0 Amps...

hi guys, Where is best to get some decent quality drive shaft boots for a B16? Seem to remember Orem Honda ones are mega money... Thanks, John

hi guys. As title, anyone got the components I need for the hydraulic clutch setup for an S4C/S80? Many thanks, John

Hello guys, I have a B16A forged bottom end using Wossner 12.5:1 high compression Pistons and a B16B head (standard but flowed). I must admit I don't know the actual assembled compression but everything's down to the bare bones to try and get it as high as possible. Engine uses throttle bodies...

Hi guys, Looking for a stock bottom pulley from a B16B. Also a Power Steering pump with brackets and bolts from a B16B. Let me know if you have anything. I'm based in Newcastle. Regards, John

hi guys, As title please. I need both mounting brackets and all bolts please. Needs to be v-belt style pulley to suit bottom pulley. Thanks, John

Hi guys, I know this is a heavily touched on subject but I haven't see a clear-cut answer on whether or not you can use this location. I want to read pressure and temp from the location seen below. Can anyone tell me if this location actually works ok as a reliable source. I understand that...

Hi guys, Can anyone please tell me the circled threads into the gearbox on an S80 for the main gearbox mount? I just need the internal thread into the box, I've removed the studs. Many thanks, John

Hi all, My engine was built up recently and I want to avoid disturbing it. The end cap which fits on the end of the exhaust cam near the V-TEC solenoid is missing. I know most types slot in and are ribbed both sides of the cam carrier - I would prefer one that simply pushes in from the outside...

Hi all, I could do with some advice please. I use this cambelt mount and this gearbox mount in my rally car - i have no idea what model Civic they are from but i need some tougher aftermarket ones - ideally with poly bushes that i could replace every few years. Can anyone link me to kits that...

Evening folks, I'm having a B16 engine built for my rally car. Current spec is:- B16A block all balanced with polished crank, Eagle rods, 81.5mmWossner high comp pistons (estimate 13.5:1 ish depending on HG). Genuine oil pump and belts. I'm using a standard but ported B16B cylinder head with...

Hi guys, I have a built B16 build underway. It uses a B16A block and EK9 B16B head. I need a full engine assembly gasket kit but don't want to buy a cheap gasket set. I have priced OEM from Honda as i would prefer OEM quality for it. Questions are:- With my build, i'm guessing an EK9 B16B...

Hi guys, Possibly a subject that has been asked many times already but every bit of info I’ve found seems a bit muddied. I have forged rods and pistons for my high comp N/A build with a lightweight flywheel, paddle clutch but OEM B16 crank/ancill pulley. The whole lot is going to get...

Hi folks, As title please, needs to be a 4-2-1 and with a 2.5" collector for B-Series. Minor scuffs and scrapes aren't a worry, please no huge dents or cracks. Thanks, John

Hi all, Guessing this question may have been asked hundreds of times but has anyone bought from this seller? Eagle ESP H-Beam Rods for Honda B16, BRAND NEW! | eBay Price wise it seems too good to be true...? Also, does anyone use them with Wiseco pistons? Compatible? Thanks, John

Hi guys, I’m looking for a Moroso sump for my B16 powered rally car. Underbody clearance with the sump guard fitted is an issue. Does anyone know if the Moroso sumps are shallower than a stock B16A1 OEM sump like I’m using - to give me more clearance and able to me to raise my sump guard...

Hi All, Looking to buy a set of OEM B16B Cam Gears. Ideally with bolts and washer please. What have you got? Thanks, John