Samples of Sold Aftermarket Parts
Please find a small selection of previously sold aftermarket parts below, for a full list of previously sold parts, please see the link -
Sold Aftermarket Parts
Item: A-Tech Final Speed Gear R Alloys
Reputation: K's Circuit Feedback
Price: £250.00 + Delivery
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Rare Final Speed Gear R Alloys in 16x7 ET48, generally in ok condition just has some marks/scratches, and various kerbing marks as shown in the pictures below, could benefit from a re-spray ideally, come with red(pink) valve caps, no tyres included.
Pictures:
Item: BuddyClub P1 Alloys
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 5/10
Description: BuddyClub P1 Alloys in 16x7.5JJ +12 Fitment, they will not fit on an EK9 with out either arch modification or high suspension, when fitted with BC Coilovers that had been lowered significantly they hit on the arches. Due to the low offset they also extend slightly past the OEM wing line, ideal for use on a track car. Wheels could benefit from a re-spray, have varies scratches, small bits of paint flake and other small kerb/damage marks, but are not cracked/bent or dented.
Pictures:
Item: Bored Throttle Body
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Bored Throttle Body, includes all sensors. Intake opening has been bored to 65mm, with manifold side being 62mm.
Pictures:
Item: Cusco Rear Strut Brace
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Cusco Rear Strut Brace, in good condition just with some marks and scratches to the bar, the mounting brackets have some small patches of surface rust on them. Requires the interior panels to be cut to fit.
Pictures:
Item: TM Works Ignition Leads / Earth Straps
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: TM Works Ignition Leads with Earth Straps on each lead for better grounding/spark. In fairly good condition overall just with some surface dirt & marks. A couple of the earth straps have some splitting in the rubber sheathing but this is not an issue. Removed from a running car & worked with no problems, will require permanent removal of the spark plug cover to run due to the added height/earth straps.
Pictures:
Item: Spoon Uprated Valve Spring Set
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 10/10 (Brand New)
Description: Spoon Uprated Valve Springs, all 16 (Intake/Exhaust), ideal for doing an engine rebuild.
Pictures:
Item: Spoon Polished Valve Set
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 10/10 (Brand New)
Description: Spoon Polished Valves, all 16 (Intake/Exhaust), ideal for doing an engine rebuild. Retail on these is around £800.00.
Pictures:
Item: Recaro Lower Seat Rail
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Recaro Lowered Seat Rail for EK9 Drivers Side Recaro, in fairly good condition just with some marks and scratches. This is not a modified standard EK9 Recaro Rail - it is a lower rail that could be purchased seperately. Lowers the seat around an inch, does not include any mounting bolts.
Pictures:
Item: Bride Lower Seat Rail
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Bride Seat Rail for Drivers Side, to be used with aftermarket bucket seats that mount from below, in fine working condition just has some small rust patches and paint flake in various places.
Pictures:
Item: Top Fuel Version II Intake
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Top Fuel Version II Intake, in fairly good condition just with some scratches, pitting and marks to the intake piping, the carbon section has a few small scratches and there is some small flaking on the filter as shown.
Pictures:
Item: BRIDE Zeta 3 (FRP Silver Glitter Back/Black Fabric with Gradient Cushions)
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 9/10
Description: BRIDE Zeta 3 Bucket Seat in FRP with Glitter Back, Black Material with gradient cushions. In very good condition, having been used for only around 6000 miles. No marks/rips/tears or loose threads to the material, with only some small marks to the side of the seat where the seat rails have been fitted, but these marks are hardly noticeable when the seat is fitted to a rail and mounted into the car, seat also comes with the back protector section to stop the back of the seat getting scratched/damaged. Seat also includes official fitting documentation, official BRIDE certificate (which matches the code on the seat) to confirm it is genuine and a sticker.
Pictures:
Item: J’s Racing ECU
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: J's Racing P73 ECU for a B18C Engine, in full working condition just with some marks and scratches all over. This ECU bears a sticker saying "Suzuka Circuit Rd.4" which indicates that it may have been tuned slightly differently and used in one of the actual J's Racing Cars, however I cannot confirm - specification of another J's Racing ECU I have is largely the same as a Spoon ECU, lowered VTEC engagement by roughly around 300-400RPM and increased Rev Limit by roughly around 300-400RPM and increased fueling. Generally works better in conjunction with other modifications, such as a good intake/exhaust system.
Pictures:
Item: Buddyclub Low Seat Rail (Drivers)
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Buddyclub Low Side Mount Seat Rail for Drivers side, in fairly good condition with just small marks and surface scratches all around.
Pictures:
Item: Front Camber Arms
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 5/10
Description: Front Camber Arms, unknown make but look to be made as the OEM Arms as they have the same markings as OEM Arms. All bushes/bolts in good condition, just some rust on the arms and could benefit from a respray/tidy.
Pictures:
Item: HKS/Vanner Lower Seat Rail
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: HKS/Vanner Seat Rail for Drivers Side OEM Recaro, Rail is in fine working condition just visually has patches of surface rust and paint flake/scratches.
Pictures:
Item: Racing Gear (Stopping Revolution) Front + Rear Brake Pads
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 10/10 (Brand New)
Description: Racing Gear SR Front + Rear Brake Pads, very popular in Japan - designed to be used on the road and also for track use. Key points being: Efficient at high temperatures (up to 400degrees), low brake dust, firm upon standard driving and increase braking force over similar pads.
Pictures:
Item: Bride Artis Bucket Seat
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Bride Artis Bucket Seat, black fabric with purple/maroon FRP back. Generally in good condition throughout, two small burn (blim) holes in the right bolster, but the rest of the fabric is rip/tear free, the back has some small surface scratches and marks but no excessive damage.
Pictures:
Item: TAKATA MPH341 4-Point Harness + Shoulder Pads
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 9.5/10
Description: TAKATA MPH 341 4-Point Harness Purchased nearly 2 years ago, only installed them a few months ago and were used for no more than 200miles before being removed and put back in the box. Shoulder pads are still in wrapping and were not used with the harness, may be the slightest smallest marks from installation/removal but I cannot see any. Includes all fitting ringlets and bolts. Harness expiry date is 2015.
Pictures:
Item: Spoon Twin Block Calipers
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Spoon Twin Block Calipers, in good condition overall. The front of the calipers are faded from use, and therefore the calipers could benefit from a refurb/spray all over - all other parts are in good condition and the calipers include all parts necessary for fitment.
Pictures:
Item: FEEL'S Low Seat Rail
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: FEEL's Lower Seat Rail in fine working condition, just visually has a few patches of surface rust to the main rail and the mounting brackets, and paint wear/scratches where the rail slides back and forward and to the main body.
Pictures:
Item: Top Fuel Air Intake
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 5/10
Description: Top Fuel Intake, in ok condition just with surface scratches and marks to main intake tube, small splits to the rubber sections and filter has some carbon peel and rust to the bottom.
Pictures:
Item: Seeker GT2 Bucket Seats
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 8/10
Description: Very rare Seeker GT2 Bucket Seats, unsure of any other set in the country. Material is in very good condition with no marks/rips/tears or loose material on both seats, cushions are in good condition to. There are a few various small scratch marks to backs of both seats, and a few grazes to the bottom but they are very minimal and will not been seen when fitted. The colour scheme is designed to be used with an FD2 to match the interior, but as most Type R interiors are (red/black) they will go with anything.
Pictures:
Item: Ohlins Coilovers
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 8/10
Description: Ohlins Coilovers for a EK9, high specification coilovers with pillow-ball top mounts (front and rear), 32-way adjustable and with very high build quality. Costing in the region of over £2,000.00 new. The coilovers have a few small marks from installation and removal to the main cups, and to the rings from adjustment, and a few tar/dirt marks but no leaks, etc. Please note, I am selling these for a friend so any queries might take a while longer to be answered as I will have to pass the questions on to him. These were removed from an EK9 imported from Japan hence the very good condition, and have not been used on the road since - only fitted to a shell to move it around during its build. Coilovers come with all documentation and 2 Ohlins C-Spanners for adjustment.
Pictures:
Item: Bride Low Seat Rail
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Bride Side-Mounting Seat Rail for Drivers Side, in fine working condition just has some small rust patches specifically to two of the mounting brackets and paint flake in various places.
Pictures:
Item: Spoon Throttle Body
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Spoon Throttle Body, has been bored out to 70mm on the intake side, but retains the 64mm on the intake manifold side.
Pictures:
Item: Mugen Air Intake
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Mugen EK9 Air Intake, in fairly good condition with just a few surface scratches and marks, comes with the velocity stack, filter and the snorkel. Does not include an OEM Intake pipe or brackets.
Pictures:
Item: Seeker (Racing Gear) JTC N1 Coilovers
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Seeker/Racing Gear JTC N1 Coilovers, with Swift 16/14 Springs. In good working condition, with various marks and scratches to mounting points/springs. Also has some marks/chipping to the locking rings. Please note the picture shows DC2 Mountings, but I have the EK9 ones. I can provide both mounting sets, and spare springs/coilover assemblies for an additional cost.
Pictures:
Item: Spoon 4-2 Manifold Section
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 7/10
Description: Spoon 4-2 Manifold, in good condition with no dents/cracks but could benefit from a good clean/polish. Is stamped B16A on top of section, as this 4-2 piece is recommended for the B16A/B16B and B18C engines. Does not include any studs to fix to the 2-1 section.
Pictures:
Item: Ogura Racing Clutch + Flywheel
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: Ogura Racing Clutch (ORC) Metal Single Plate Clutch and Flywheel Kit, removed from a running engine and in good working condition. A very popular kit, rated up to 300PS so is suitable for most Honda applications, can be fitted to B16B and B18C Engines.
Pictures:
Item: MeisterR Zeta S Coilovers
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 6/10
Description: MeisterR Zeta S Coilovers, removed from Banana's EK9 (Front Damaged), but the fronts have been installed to another EK9 to test and they are in perfect working condition. Has various paint flake/scratches but are generally in ok condition.
Pictures:
Item: J's Racing 3D GT Wing
Reputation: K's Circuit Feedback
Price: SOLD
Payment: Paypal/Bank Transfer
Location: Bath
Condition: 8/10
Description: J's Racing 3D GT Wing, a must have for some serious track/racing action! In very good condition with a few small minor marks from storage. Has had very little use but could benefit from a good clean/polish. Does not include any brackets, but I am waiting for a quote on them from J's Racing, the price listed is for the wing without brackets, as some substitutes/generic ones would not be to costly.
Pictures:
.jpg)
/Seeker%20GT2%20Seat%201%20-%201.jpg)
