EK9_eater said:Why are they so ****?
They have 180bhp, LSD, do 0-60mph 5.5sec and they only do 1/4 mile in 15.5? thought they would do it in V. low 14's?
elmo said:I'm guessing your american?? The country where standard integra type R's do a 1/4 mile in 13 flat.......................
wouldnt say ek9's are **** to be honest, what do you drive?
SpoonCTR said:tuning on a dyno its the secret I think
blinx9900 said:it certainly is. the next best thing is a street tune with aem ems.
SpoonCTR said:aem ems hmmmmm thats way to much money
blinx9900 said:i agree, come to think of it, you can street tune with CROME PRO also. its not as powerful, but for cars making under 400hp it should be excellent.
SpoonCTR said:I prefer a chipped p28 ecu, with a custom map based on mods lol
I wrote that guy and email but i didnt received any response, i want to buy a chipped ecu from him, i dont know if it is possible to exchange chips on the ecus, because i'm planning on having 2 motors, one b16b and a b20 heheheblinx9900 said:you just described a crome basemap. check out www.phearable.net this guy can do it, tell him revhard sent you. you tell him what you got and he makes a custom basemap for your set up, i have an allmotor basemap on its way right now (i ordered it before i decided to boost it), i'll let you know how it goes.
rvm said:I wrote that guy and email but i didnt received any response, i want to buy a chipped ecu from him, i dont know if it is possible to exchange chips on the ecus, because i'm planning on having 2 motors, one b16b and a b20 hehehe
do you know anyone in [FONT="]j-k-tuning.com ? that guy responded my email quickly, has better prices than phearable.net
[/FONT]
blinx9900 said:j-k and phearable are competitors, there both good, and yes you can have more than one chip for an ecu, as long as its socketed (phearable and jk ecus are all socketed) the socket makes it so you can swap chips by just popping them in and out, or if you already have an ecu you want socketed and chipped they can do that too, the reason phearable didnt respond to your email is because its new year and hes in florida so he might have been either partying of sleeping. jk must have lowered his prices, before they where more expensive. both good guys, i'll let you know what i think of my phearable chip, should be here anyday now.
blinx9900 said:he does make sure to tell him revhard sent ya.
my ek9 has been timed @ 6.1 secs to 60 mph and a 15.1 1/4 mile ,and has a 4-1 dc JDM header,full spoon n1 ,itg maxogen,sports cat,ultra leads,irrdium plugs, so how do you get 7.5 seconds to 60 mph? when my ek9 is quicker than my frends ep3 2.0 type R civic with a few mods ????????? which has a factory 0-60 mph of 6.6 seconds ???????webartie said:the ek9 definatly does not do 0-60 mph in 5. ish seconds its more like 7.2-7.5 that said there not the worst 1/4 mile
that 5. ish sec to 60 is written everywhere!!!! ha ha
rvm said:Ordered my ecu today! i hope he sends me a good base map for my stock b16b motor! He will put vtec point at 5300 and 8900 rev limit
And i mentioned you on the refferrer part
blinx9900 said:awesome! why did you choose such a low vtec cross-over point? your car might bog for a second when it hits vtec if its too low.