A lot of parts off my civic. B18CR, S80 4.7FD, Mugen, ARP, Tegiwa, hondata etc.

Discussion in 'For Sale' started by that_civic, Mar 3, 2017.

  1. that_civic

    that_civic Well-Known Member

    Joined:
    Feb 8, 2012
    Messages:
    1,063
    Likes Received:
    103
    Firstly I may change bits in here if I come across an error, this was written up a while back so some parts have already gone or are no longer available. Main parts haven't been removed now yet, so anything to do with the engine will have to wait until it's been compression tested and removed, expect mid this month.

    Rep- that_civic
    Paypal or cash on collection
    Halesowen West Midlands
    All prices exclude fees and postage
    Postage worldwide for the majority of things apart from large stuff

    Approximately 50-60k miles no confirmation but do have the picture of the original clocks before the swap which show 38k and if you reg check my car you'll see I do around 5k miles a year. The car was swapped back in December 2013 from memory. Always ran on V power.


    SPECS:


    Engine:

    - JDM B18cr stamped 00 so one of the latest ones produced -

    - recent oem headgasket

    - ARP headstuds

    - oem water pump

    - gates timing belt

    - oem valve stem seals

    - head skim

    - Brand new from HondR complete distributor unit

    - rough smoothed valve cover with cam cut out

    - VMS gold adjustable cam gears

    - BWR cam seal (new and not fitted)

    - Gates low temp thermostat

    - Spoon low temp fan switch

    - alternator & starter

    - various seals and gaskets in packets

    - Mugen baffled sump bought from Ian on here a few years back

    - Magnecor red HT leads

    £1500

    IMAG0485.jpg
    IMAG0486.jpg
    IMAG0487.jpg
    IMAG0488.jpg


    Bolt ons:

    - genuine AEM fuel rail £70 SOLD

    - genuine AEM adjustable fuel pressure regulator £70 SOLD
    IMAG0490.jpg
    IMAG0491.jpg
    IMAG0492.jpg

    - PLM V2 Bisimoto style manifold with custom 3" collector To a True 3" manifold back for EK hatch (5zigen backbox not included) £500

    - Edelbrock performer X inlet manifold with Skunk2 thermal intake gasket £250

    - OEM throttle body £60 SOLD

    - Custom stainless steel 3" intake with blox 3" V stack and filter £70 (NOT THE PIPE IN THE PICTURE)[xxxencorexxx]

    - Zerg Industries thermal throttle body gasket £20



    Gearbox:

    - smooth s80 4.7 FD box (would benefit from a new clutch as the bite points right at the top of the peddle now and doesn't grip as it once did) recent box oil with land rover oil £600

    - gear linkage with hardrace bushes £50


    Other:

    - drive shafts £50

    - preface ek4 loom included £100

    - preface ek4 oem mounts included £60

    - Blackworks Racing radiator hoses £50

    -Blackworks Racing Black Radiator and slim fan £90

    - Heavy set heater hoses £20

    - Blackworks racing fuel pressure gauge £10 SOLD

    - Hondata s300 V2 Ecu and conversion harness with shift light and launch control £400 SOLD
    IMAG0498.jpg IMAG0499.jpg
    IMG_2944.JPG

    - MSD black version HT leads £40

    - lightweight Fidanza flywheel £80 [xxxencorexxx]

    - RC 440 injectors £120
    IMG_2946.JPG IMG_2947.JPG IMG_2948.JPG
    - Used and slightly faulty Distributor unit ( suspected bearings gone ) £40 SOLD

    - Tegiwa FLP rep shifter £60


    Engine made 211 at the fly at RDT with a faulty Blackworks Racing fuel pressure regulator, dodgy Blackworks Racing TPS, restrictive heat soaking intake, oem inlet and an oem fuel pump that couldn't supply enough fuel pressure. With its current spec it would make more and drivability and torque would be better however never got it remapped due to knowing I'd be going to K swap.





    The swap will be missed as for what it is, a n/a b18 it embarrasses a lot of newer more expensive cars, especially in a lightweight shell not many things can get away from it, on the track


    It would benefit from a new rocker cover as my vented Honda motor co won't be supplied, just a tatty smoothed one. Would benefit also with a new clutch as I'm sure this is still the factory one and maybe some stiffer engine mounts.



    Car is now off the road and the parts will be removed as soon as the unit space is available.


    Smoke ?

    Right now yes it does smoke, but black smoke right up top but that's due to running very rich, afr gauge shows as low as 10.2 on full throttle hence the need for a remap. NO BLUE!!!


    WARNING


    Must say with the 3" in a stripped out car can cause headaches but should be okay in a full interior car, it's not loud until above 3k revs, when vtec kicks in all hell breaks loose and will definitely get you in trouble with the sound police.


    ------------------------------------------------------------------------------------------

    Available as soon as it's out this month


    Why am I selling ? Well I've done the b swap now, although very fun and raw I'd like to do the k24 thing now , aiming for around 260-300hp this time and the only way I'll get the b18 there is throwing many thousands at it in n/a form or boosting but reliability will be sacrificed each time which won't be the case with an oem k24 swap, in theory anyways.


    None engine stuff:



    - EK hatch Tegiwa X brace £170
    IMG_1649.JPG

    - Tegiwa torque dampener for an EK £30

    - EK subframe, wishbones and PAS with ek4/9 26mm arb , has nearly new energy bushes £80

    - BNIB EK inner toe arms £15 a pair



    Pictures will be uploaded as soon as I've got it over to the unit.

    Will also get a compression test done ASAP

    Video proof of the engine very soon.



    Video below of when it was on the dyno before the head gasket and stem seals were replaced.



     
    Last edited: Mar 26, 2017 at 12:00 PM
  2. waff

    waff Active Member

    Joined:
    Jul 4, 2010
    Messages:
    211
    Likes Received:
    27
    Location:
    Spain
    Are the engine and gearbox gone? Or still available?
    Thanks
     
  3. that_civic

    that_civic Well-Known Member

    Joined:
    Feb 8, 2012
    Messages:
    1,063
    Likes Received:
    103
    Everything's still available, just putting names by parts to who've shown interest until I remove it from the car, expect next week or the week after max.
     
  4. that_civic

    that_civic Well-Known Member

    Joined:
    Feb 8, 2012
    Messages:
    1,063
    Likes Received:
    103
    Some pictures added.
     
  5. sc888

    sc888 Member

    Joined:
    Feb 16, 2009
    Messages:
    537
    Likes Received:
    9
    Is the fuel gauge on the fuel rail available ?
     
  6. monkeymk2

    monkeymk2 Member

    Joined:
    Nov 4, 2010
    Messages:
    45
    Likes Received:
    1
    Location:
    London
    Is the throttle body the itr type? Do you have a picture of the throttle body itself?

    Thanks
     
  7. that_civic

    that_civic Well-Known Member

    Joined:
    Feb 8, 2012
    Messages:
    1,063
    Likes Received:
    103
    Sold sorry.
     
  8. that_civic

    that_civic Well-Known Member

    Joined:
    Feb 8, 2012
    Messages:
    1,063
    Likes Received:
    103
    It is an oem ITR 98 spec.
    I can get you one today, it's still currently attached to the engine though.
     
  9. monkeymk2

    monkeymk2 Member

    Joined:
    Nov 4, 2010
    Messages:
    45
    Likes Received:
    1
    Location:
    London
    Sending you a PM now.
     
  10. Tahir

    Tahir Member

    Joined:
    Jun 14, 2009
    Messages:
    375
    Likes Received:
    18
    What is needed to run the hondata on a boosted setup, sure a few components needed adding/changing?
     
  11. that_civic

    that_civic Well-Known Member

    Joined:
    Feb 8, 2012
    Messages:
    1,063
    Likes Received:
    103
    Don't think anything on the ecu will need changing, the map will be changed to suit of course. Think to run boost by gear though you need a component but again not too sure.
    Reckon @jesse888 could clarify this for you, he's pretty clued up on mapping boosted stuff.
     

Share This Page