98 spec Integra Type R


Then onto the good arch
Was running out of time and battery power so got done what I could
20230913_170810.jpg
20230913_170815.jpg
 
Last edited:
Handy trick for anyone painting parts and needing space for drying. Use an apartment green house,very handy and reduces over spray

20230913_151931.jpg
 
awesome work on the restoring, hopefully back to shows soon
 
Late start today but got the tank down and most of the left arch cleaned back. Started some of the boot floor aswell.

All good above the tank,all dry surface rust thankfully. Some seam sealer applied on rear left after epoxy 1k primer

Started on the boot floor and rear chassis leg so hopping tomorrow ill have the boot floor done and a start on the other arch
20230914_150132.jpg
20230914_155151.jpg
image-1000x1000.jpg.png
image-1000x1000.jpg.png
image-1000x1000.jpg (1).png
image-1000x1000.jpg (2).png
image-1000x1000.jpg (3).png
image-1000x1000.jpg (4).png
image-1000x1000.jpg (5).png
image-1000x1000.jpg (6).png
image-1000x1000.jpg (7).png
20230914_174738.jpg
image-1000x1000.jpg (8).png
image-1000x1000.jpg (10).png
 
Love a good rebuild thread! Gives me motivation to fully strip my EK down to the shell in the next year.
 
Love a good rebuild thread! Gives me motivation to fully strip my EK down to the shell in the next year.
Thanks man,its a lot of work. I wanted to start it during covid but I had to build a pro spec drift car and my own car in 6 weeks then. Regret not getting more parts then as alot is getting so hard to find.

If you even do a corner of the underbody at a time it'll make the difference and takes the pressure off
 
Got a bit more done on Friday, have the boot floor in epoxy and the left side is all in sealer. Rear panel is now in its first coat of high zinc epoxy primer.
Back to work next week so probably only going to gat a day each week at it now. Important part is that its started

Everything was brought back to bare metal,some areas had factory sealer covered in multiple layers of black shutz which did preserve the metal but looked like dung and was a nightmare to remove. I'm using an m18 milwaukee grinder with the 8amp battery and a knotted cup brush,when it hits the black stuff its like hitting the brakes. I sprayed some petrol on and it did soften it but I found a low flow butane torch made the biggest difference to soften it.

When it was back to metal I used bardahl convert,ox on any surface rust areas but also any metal incase of microscopic rust pores i can't see. I then put on a dust coating of pro xl epoxy 1k and 2 thick coats before seal sealer. After this I will put on a thick coat of high zinc epoxy before 2 coats of white stone guard and then QD enamel paint in champ white. Im doing this once and want it to last
image-1000x1000.jpg (13).png
image-1000x1000.jpg (14).png
image-1000x1000.jpg (15).png
image-1000x1000.jpg (16).png
image-1000x1000.jpg (16).png
image-1000x1000.jpg (18).png
image-1000x1000.jpg (20).png
image-1000x1000.jpg (21).png
image-1000x1000.jpg (22).png
image-1000x1000.jpg (23).png
image-1000x1000.jpg (25).png
image-1000x1000.jpg (24).png
 
Last edited:
Love to see this level care being put into these cars! Hoping to get my full underside done through the winter so the car lasts another 25 years keep it up man!
 
A few weeks away from the car due to metal in my eye and alot of work fatigue,hopefully back at it this week.






Sorted some service history and accounted for what bits iv bought



20231015_134914.jpg




Got some more OEM bolts and clips for the back end


20231015_130327.jpg





Bought some hardrace rear roll bar bushes as oem jdm size inners were no longer available


20231015_140904.jpg
IMG-20231015-WA0006.jpeg




And won a set of 98 spec OEM JDM rear mudflaps after searching for a number of years to get a clean set




20231015_140947.jpg
 
Last edited:
A few weeks away from the car due to metal in my eye and alot of work fatigue,hopefully back at it this week.
Thats always a bugger. Hopefully they got it out easy enough without that glow dye stuff?
 
Thats always a bugger. Hopefully they got it out easy enough without that glow dye stuff?
Not this time thank god but did use numbing gel so had to sit outside for an hour before driving after waiting 8 hours
 
Got the rear right arch into primer. The inner lip of the arch needs attention but nowhere as bad as I expected thankfully.
The usual stripped back to metal,treated with de oxidiser then a thick coat of novol epoxy primer

20231017_194846.jpg




20231017_205335.jpg




20231017_210507.jpg


Just for comparison,I'm size 13 shoes and thats one the amount of crap from one arch,approx 2 inches thick

20231017_201427.jpg


My hord of engine parts so far

20231017_192007.jpg



Rear suspension hord so far

20231017_192349.jpg
 
Good progress there!

Amazing how much rubbish came off the one arch

That eye numbing stuff is a right nightmare, but at least its sorted now
 
Back
Top