Search results


  1. Teamdiesel

    Dyno test results!!!

    I haven't been on here for a while but I want to share my new dyno results. Here is the setup for those of you that don't know: 85.5mm Darton sleeved GSR block 85.5mm Wiseco custom forged pistons (13.5:1 cr) Crower Max lite billet rods Crower 92mm forged crank OEM rod bearings ACL main bearings...
  2. Teamdiesel

    We need your vote!

    Hello everyone, my girlfriend is a contestant in this years Antigua Queen of Carnival contest. Her name is Sharlene Coulthard and they are having a poll on "Who will be Queen". I would greatly appreciate if you could go to this link and vote. Who will be Queen?
  3. Teamdiesel

    New updates on my build!!

    I have encountered a small problem with my previous build, where my Golden Eagle sleeves started to chip/corrode at the top due to coolant/water mixtures over a period of time. Now, my philosophy is when you go down you come up bigger! This prompted me to sell most of the parts within that build...
  4. Teamdiesel

    Please post up pics of CTR's with CF rear trunks!

    I and contemplating on buying a carbon fiber rear trunk for my CTR and would like to see pics of them installed.
  5. Teamdiesel

    a few new vids of my EK9 in the 1/4 mile

    Just a few new vids from last few weeks. Does 12.6-12.9's throught the quarter. YouTube - Type-R MADNESS!! YouTube - Civic Type R (EK9) YouTube - Diesel Vs Kris I lost this last one because it was a bracket race where I had to give the slower car a handicap. I red lighted so they...
  6. Teamdiesel

    85x89 dyno tuned

    Well, the car made a 12.7 pass in a full interior 2558 w/driver EK hatch and about 214/154 on a partial tune. So I decided to retune fuel and cam gears to see where I can go. The setup is: 85x89 sleeved GSR block Skunk2 Pro IM Skunk2 Stage2 cams Skunk2 Pro cam gears Hondata IM gasket...
  7. Teamdiesel

    NA Best 1/4 mile time

    I did my personal best at the drag strip last night. Here is the breakdown. reaction......0.782 60ft...........1.712 mid mph......84.27 660............8.047 E.T............12.704 mph...........106.38 This was done in a full interior, NA tuned EK9 with a 250lb driver:angry:.
  8. Teamdiesel

    New personal best 1/4 mile time!

    I just changed my Edelbrock PerformerX Intake Manifold to a Skunk2 Pro series manifold and she pulls like a freight train. Went to the track without tuning for the new manifold and managed a personal best of 12.923 @105mph ALLMOTOR! I could have achieved a 12.8 with a better 60ft, but the track...
  9. Teamdiesel

    Incar vids of my CTR drag racing.

    I decided to head to the track last night and ended up kicking all asses lol. Here is my setup: 85mm GE sleeved Gsr Block 89mm balanced LS crank 11:1 Wiseco pistion Eagle rods ACL bearings B16B head (stock) Supertech Springs/Retainers S2S2 cams S2 Pro cam gears Hondata heatshield...
  10. Teamdiesel

    New vids of my Civic Type Rx last saturday

    here are some vids of saturday night. I am the civic hb without the right headlight. The Integra Type R in the second vid was squeezing a 50 shot of nos and still got whipped :). YouTube - Teamdiesel civic vs HeadHunter turbo starlet YouTube - Teamdiesel civic vs Street Reapers Integra Type-r...
  11. Teamdiesel

    New dyno numbers!!

    I just came from the dyno and want to share my numbers :) I ran the car at the track last night and got 13.5 @107 mph on STREET TIRES, not on slicks. This is where the before and after tuning graph.
  12. Teamdiesel

    New dyno numbers with new setup :)

    My previous 1.8lt setup gave me 193whp/134wtq with an open header and a custom 3" longtube cold air intake. These new graphs were done with a quick street tune by myself, and with FULL exhaust and a short ram intake. The best run was 210whp/150wtq, but I couldn'd get that graph loaded.
  13. Teamdiesel

    She is alive!

    I just finished putting together my engine today, which has been in a building process for some time now. I have been collecting, researching, and analysing many things to complete this motor the right way. As most of you all know, I had spun a rod bearing on my previous 1800cc engine. I saw it...
  14. Teamdiesel

    Spuna rod bearing, new project rises.....

    Well, I was at the track abouta month ago and had a little mishap where my dipstip skyrocketed at 9500 rpms and flooded my engine bay with oil. My pitcrew must have checked my oil before a race and forgot to push the dipstick all the way down. A spun rod bearing was the result. Most people...
  15. Teamdiesel

    Hot video of my CTR drag racing with an Mfactory gearset!

    Thos of you who know me know that I am a stroke 1.8lt CTR engine with a few extra goodies. I had just installed an Mfactory 3/4/5 gearset and wanted to share the phenominal experience that it has brought to me. Inthis video I am drag racing a turbochared Premiera. YouTube - Diesel " DCAIS"
  16. Teamdiesel

    New personal best 1/4 mile time

    I just came from the drag strip and the car is working on clean! She did a 13.535 @ 97mph with a missed 4th gear:nerv:. She has the potential to do 13.2-13.4 NA, buth the gearbox began to feel tight so I called it the night. This is all on a NA CTR:win:. All motor baby!!!
  17. Teamdiesel

    Finally stroked my B16B, pics and info inside.

    Well fellas I finally finished my build. I stroked my B16B to 1.8lts of joy. Details of build are listed below: B16B 11.5:1 forged Wiseco pistons Eagle forged H-beam rods APR rod bolts ACL Race bearing kit ITR crankshaft Hytech replica 4-2-1 Tri-Y header Omni 2.5" testpipe Mfactory...
  18. Teamdiesel

    My new 2000' Civic Type RX

    I just got her from Japan on Monday. Tell me what you guys think.
Back
Top