Search results

Anyone fitted a set of Skunk2 front camber arms before? The new bushes has slightly bigger hole than the stock bolt... 11.21mm approx. (see photo) (brought off Tegiwa) The bushing holes are all measured 11.21mm, but the standard bolt to mount is only 10mm. (it's recommended to use the...

Hi all, I am looking to buy a new set of brake dust shields as my ones are getting old rotting away. are these brake dust covers / shields sits behind the brake discs available to buy? Are they the same as DC2 and all other EKs EJ models? anyone know where to buy them from, please link or...

Looking for a new b series half shaft with new bearing in it. (or very good condition will last) seems so hard to find these days. Anyone have any for sale or know any good quality shafts for sale ? Cheers fellow EK owners!

looking to buy an EK Speedo, my speedometer has died and need replacement Let me know if you have one up for sale, Please share pictures and price / location Thank you

Hi all, bit of an issue, I got round to fit the s80 LSD gearbox in the car, but after the gearbox change, speedo has stopped working, I swapped back to the original speed sensor and it's the same, no reaction on the speedo at all. Any ideas on the issue and what else I can look at to the...

Looking for the plastic cover on the left side of the passenger seat, please let me know if anyone has a spare cover or where I can get one from. Thank you

Hello, it's probably time for a new battery for the EK. would welcome any recommendation for a new battery. Please share links or recommendations on new batteries. Thank you

Hi Guys, hope it's all well, thought i would ask some of you on here, my car is has been in my garage for some months for a DIY restore project, regularly started and I do work on the car over weekends and evening especially with the lockdowns. recently, the ABS warning light came on, i have...

hello all, Hope it's all well, I am now based in Manchester and not seen many fellow EK enthusiasts in the region, I am hoping to get my car mapped by someone in the North West region with good B series engine tuning experience, ECU wise, it's a Apexi power FC, would be grateful if anyone...

Good morning all, a quick one, seems like my bad luck streak hasn't quite stopped yet, lol since the drivershaft incident at the garage, recently I paid for my front wheel bearing to be replaced, and now i am working on the EK in the garage over the winter, it looks like the mechanic did not...

Hello all, I am looking for a few bits and pieces for my EK4 P28 chipped ECU or equivalent (its a B16a2 engine fully rebuilt running ITR cams, dual valve springs + retainers, ITR inlet + 62mm throttle bodies, looking to get the car mapped) Set of Recaro Seats - (ideally black, would look at...

Hello all, This is a bit of a strange one, I am not sure how to go about it but I'm trying to be mature about this, but I am rather annoyed as the title suggests the story... here goes Wednesday morning, I dropped off my EK4 (modded) to my usual garage for MOT and to get my front NS wheel...

hi All, I am looking to map my Ek4's engine as fully rebuild ITR DC2 top end with the cams, I would like to source a good condition p28 ECU so i can get it chipped , it would be a bonus if is already chipped and mappable please get in touch ! many thanks Wils

Hi All, I am looking for replace my half shaft / intermediate driveshaft on the EK4, currently making a bit of a whining noise over 60mph. Ali (seller) is clearly state and showed me the issue, and I know it isn't a major and imediate job, but I do like to make sure all my cars are problem...

Hi All, I am looking for a decent S80 LSD gearbox for my Ek4 ! please let me know if you have one or know one for sale around! many thanks Wils

Hi All, hope it's all well, I am Wilson based in hampshire. I recently brought Ali's white Ek4 of him as my daily, I have never owned a Honda, I must say, she is a better drive than my weekender ! and the MPG is very good! not much difference in comparison to my old daily, my Nissan Micra K11...