Search results

Anyone got a set of Yellowstuffs to suit 282 Dc2 calipers? Also after rear Yellowstuffs for 242 ek4 calipers Cheers

Been a while since i posted on this forum as i have pretty much finished the work on my EK4 My key has developed an intermittent issue and wont start the car sometimes, ill put the key in the barrel and turn it, the green light doesnt stop flashing remove key and try again, doesnt stop...

Just fitted my wheels and found the nut and washer missing from the passenger side rear engine mount :S does anyone have one of these?

Does anyone have one of those metal rear diffuser bolt on puppies? not going to balls deep just something that looks sweet and sorta works, Posted too :) Cheers

i had a look on the forum quite abit and cant seem to figure out what this is :S I bought this not so long ago and not too sure what to do lol I have a Ek4 VTI Uk spec with B16A2 engine and am looking to upgrade my exhaust header, atm i have a Japseed 4-1 header (badly dented!) , Skunk2 decat...

Basically I'm after a new manifold for my ek4 as it has a large dent in the bottom pipe (4-1) I don't know the make.. Would anyone consider a part exchange for this and some money? Other than the rather large dent in the bottom it's fine lol I'm after 4-2-1 purly for ground clearance *edit...

Hey guys, got enough money finally after a payrise to sort out the mapping on the ek4. Has anyone bought one of these socketed and chiped p28 ecu's from H tune? Are they any good? http://h-tune.co.uk/socketed-and-chipped-obd1-p28-vtec-ecu1-5257.html If so I'm assuming that they still need...

Am looking for the drivers side rear facelift hatchback light as mine got smashed.. :(

I am fitting an S4C LSD gearbox to my ek4 and am looking to replace my flywheel with a lighter one, not stupid light as it is my daily but can't stand the slow pickup of the standard b16a2 one!! Cheers

After splitting my gearbox I found that one of the gearbox oil seals was shagged, does someone have a pair of these as I want to change both of them together, I'm not sure what oil seal it is or it's number but it's the big one that the driveshafts go into.. Hope that narrows it down haha And...

I sorta cooked my brakes round brands hatch and am after something abit better now! I'm after a set of fancy drilled/grooved discs front and rear, again ideally not brand new as can't really afford it, and some decent high performance pads track ready style :) Cheers

Just changing my airbox over to a mugen one :D and just found this?! Where does it go? Could this be why my engine light is on? Anyone know what it's off? Cheers

Just got myself a s4c lsd gearbox out of an ek9 with 60,000miles on it and apparently doesn't go into 5th or reverse. Is this a common problem? And is there any guide on the forum of how to strip these? My old man reckons he used to do gearbox repairs on vans and other vehicles just wondering if...

I'm looking for a SET of red harness's 3 or 4 point ideally 3 as there slightly cheaper but has to be red. sparco, luke etc Cheers

Recently I adjusted my rear camber and never measured it just kept an eye on wear, but I had the car aligned before and after having the camber and the toe hasn't changed that much considering the camber went from -0.57 to -4.25 What I was wondering is there a table or chart that can be made...

Basically was wondering the handling level of these cars, why and comparisons etc modified and not, you get the drift Cheers

Anyone going abroad in the next few weeks and wants to buy me a set of spc front cambers for ek? Or got a set to sell? Cheers

For a little while now the front left of the car kept knocking over low speed bumps and dips in the road. Not fully sure what it is but recently it got alot worse! Atm I have the rear of the car jacked up and am trying to investigate where this rear knocking is coming from! I think it is the...

As the tittle says I have bought dc2 camshafts, double valve springs and retainers and am looking to fit these relatively soon, was wondering while the head is off is there anything worth doing and anything I should be carful off or anything to note whilst taking the head off etc. also am...

I bought a ctr replica spoiler and it had a ek4 baseplate so I'm after ideally a replica base plate? Or a b16b baseplate Cheers