Search results

Getting painted so doesn't have to be a minter, let me know what you have. Cheers.

Does anyone know the parts numbers for all the fixings for genuine EK9 prefecalift front and rear lips please? Bodyshop have lost mine so need some new ones. Thanks.

Any EK aftermarket spoilers for sale out there? Especially Spoon (rep)? Not too fussed on condition as want to change from stock before the car goes to the bodyshop for a full respray. Cheers...

As title, don't need bulbs and decent condition please, thanks...

Got one I want to fit to the EK3 so I can add an EK4 ARB, I know I can fit it without but looks better and has all the bolts supplied (and may want to go bigger arb in the future), basically the thing looks fine, I'm just a little dubious at using the supplied LCA bolts, they seem sturdy enough...

What's out there, been looking at new but want to see what's about second hand too, need to be reclining and in great condition, preferably with rails ready for the crx but let me know what you've got...

So when I got the car it had a slight weap from the cam end seal and the vtec solenoid. Other than that everything working super fine. Engine bay looked like this when I got it... So a few days back we decided to tackle everything... PasswordJDM cam end seal done New Honda vtec...

Think they are all the same fitment however it's for a D15Z6 engine, one in decent condition as bought one already that was no better than the one crap one it replaced. Let me know what you have, am near Newark in Nottinghamshire. thanks...

One of mine has just stopped working and I have 2 kids so needed ASAP, it's the lower part that bolts just under the rear bench, had a few inches of seat belt and ends in the PUSH end that the buckle fits into, must be loads around from stripped out cars, shame it just went after I scrapped my...

I just need minimum of 8, 2 for each wheel not fussed on condition as just for a rolling shell not to be driven, just to hold on the spare set of wheels so cheap as possible, cheers... J.

Looking to replace my ek3 as shell no good, would ideally like white or dark grey metallic but open to whatever for the right car, mileage not an issue but needs to be a rust free shell, don't mind some work to do either as will use other as a doner, light mods ok would mainly be interested in...

Started last night on the ek3, turn the wheel either way and there's a squeaking noise as it turns in either direction, at any speed and stationary too. Sounds worse from outside than inside too, strange but it doesn't sound mechanical although it's directly related to how fast your turn too...

as title, had the rear bumper of today and no matter what we tried it didn't fir right have drilled a few holes in the bumper to try line the fixing bolts up but for the life of us we couldnt get it done right, any tips, tricks, guides, pics etc to help get it done, or anyone got a cheap ek9...

Have an ek4 rear ARB, brackets, bushes and droplinks as a little upgrade to my ek3, just need the 4 bolts that attached the brackets to the rear subframe, anyone know what spec/size bolt's I need please? thanks...

need both side door handles (no locks), can be any colour, basically want to colour match mine on the ek3 but need to use the car daily so want a spare set cheap to get ready for a quick swap. cheers...

I bought an ek9 front and rear lip to paint and fit to my ek3 pre-facelift, fitted the front a week or so ago no problem, however when I came to fit the rear yesterday it fits the bumper fine and snug but at each wheel arch it overruns about half and inch, any ideas? It's all OEM Honda, may I...

Had a quick look at the fixings and couldn't get it to budge is there a trick of were to pull etc or a hidden fixing? any help appreciated, cheers...

for an ek3, need bar, brackets, bushes and bolts, cheers...

As the titles really, seen some nice EG LCA's at a good price and wanted to check they'd be the same fitting as an EK, thanks...

Wanted to move the stereo down to the bottom console spot, anyone done this here? Have seen it done but don't know if there's any special brackets etc that you need or how easy it will be with cable lengths etc. any help or ideas welcome, thanks...